CY7C1371D
CY7C1373D
18-Mbit (512K x 36/1M x 18)
Flow-ThroughSRAMwithNoBL™Architecture
Functional Description[1]
Features
• No Bus Latency™ (NoBL™) architecture eliminates dead
The CY7C1371D/CY7C1373D is a 3.3V, 512K x 36/1M x 18
Synchronous flow through Burst SRAM designed specifically
to support unlimited true back-to-back Read/Write operations
with no wait state insertion. The CY7C1371D/CY7C1373D is
equipped with the advanced No Bus Latency (NoBL) logic
required to enable consecutive Read/Write operations with
data being transferred on every clock cycle. This feature
dramatically improves the throughput of data through the
SRAM, especially in systems that require frequent Write-Read
transitions.
cycles between write and read cycles
• Supports up to 133-MHz bus operations with zero wait
states
— Data is transferred on every clock
• Pin-compatible and functionally equivalent to ZBT™
devices
• Internally self-timed output buffer control to eliminate the
need to use OE
All synchronous inputs pass through input registers controlled
by the rising edge of the clock. The clock input is qualified by
the Clock Enable (CEN) signal, which when deasserted
suspends operation and extends the previous clock cycle.
Maximum access delay from the clock rise is 6.5 ns (133-MHz
device).
• Registered inputs for flow through operation
• Byte Write capability
• 3.3V/2.5V IO power supply (V
• Fast clock-to-output times
)
DDQ
— 6.5 ns (for 133-MHz device)
Write operations are controlled by the two or four Byte Write
Select (BW ) and a Write Enable (WE) input. All writes are
conducted with on-chip synchronous self-timed write circuitry.
• Clock Enable (CEN) pin to enable clock and suspend
operation
X
Three synchronous Chip Enables (CE , CE , CE ) and an
• Synchronous self-timed writes
• Asynchronous Output Enable
1
2
3
asynchronous Output Enable (OE) provide for easy bank
selection and output tri-state control. To avoid bus contention,
the output drivers are synchronously tri-stated during the data
portion of a write sequence.
• Available in JEDEC-standard Pb-free 100-pin TQFP,
Pb-free and non-Pb-free 119-Ball BGA and 165-Ball FBGA
package.
• Three chip enables for simple depth expansion
• Automatic Power down feature available using ZZ mode or
CE deselect
• IEEE 1149.1 JTAG-Compatible Boundary Scan
• Burst Capability — linear or interleaved burst order
• Low standby power
Selection Guide
133 MHz
6.5
100 MHz
8.5
Unit
ns
Maximum Access Time
Maximum Operating Current
Maximum CMOS Standby Current
210
175
mA
mA
70
70
Note:
1. For best-practices recommendations, please refer to the Cypress application note System Design Guidelines on www.cypress.com.
Cypress Semiconductor Corporation
Document #: 38-05556 Rev. *F
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised July 09, 2007
CY7C1371D
CY7C1373D
Pin Configurations
100-Pin TQFP Pinout
DQPC
DQC
DQC
VDDQ
VSS
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
1
DQPB
DQB
DQB
VDDQ
VSS
2
3
4
5
DQC
6
DQB
BYTE C
BYTE B
DQB
DQC
DQC
DQC
VSS
7
8
DQB
DQB
VSS
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
VDDQ
DQC
DQC
NC
VDDQ
DQB
DQB
VSS
CY7C1371D
VDD
NC
NC
VDD
ZZ
VSS
DQD
DQD
VDDQ
VSS
DQA
DQA
VDDQ
VSS
DQD
DQA
DQA
DQD
BYTE D
BYTE A
DQD
DQD
VSS
DQA
DQA
VSS
VDDQ
DQD
DQD
DQPD
VDDQ
DQA
DQA
DQPA
Document #: 38-05556 Rev. *F
Page 3 of 29
CY7C1371D
CY7C1373D
Pin Configurations (continued)
100-Pin TQFP Pinout
NC
1
NC
2
NC
3
VDDQ
4
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
A
NC
NC
VDDQ
VSS
NC
VSS
NC
5
6
NC
7
DQPA
DQA
DQA
VSS
VDDQ
DQA
DQA
VSS
DQB
DQB
VSS
VDDQ
DQB
DQB
NC
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
CY7C1373D
BYTE A
NC
VDD
NC
BYTE B
VDD
ZZ
VSS
DQB
DQB
VDDQ
VSS
DQB
DQB
DQPB
NC
DQA
DQA
VDDQ
VSS
DQA
DQA
NC
NC
VSS
VDDQ
NC
VSS
VDDQ
NC
NC
NC
NC
NC
Document #: 38-05556 Rev. *F
Page 4 of 29
CY7C1371D
CY7C1373D
Pin Configurations (continued)
119-Ball BGA
Pinout
CY7C1371D (512K x 36)
1
2
3
4
5
6
7
A
A
V
A
A
A
A
V
DDQ
DDQ
NC/576M
NC/1G
CE
A
A
A
ADV/LD
A
A
CE
A
NC
NC
B
C
2
3
V
DD
D
E
F
DQ
DQ
DQP
DQ
V
NC
V
DQP
DQ
DQ
DQ
C
C
SS
SS
SS
SS
SS
SS
B
B
V
V
V
V
CE
C
C
B
B
1
V
DQ
DQ
V
DDQ
OE
A
DDQ
C
B
G
H
J
DQ
DQ
DQ
DQ
DQ
DQ
BW
V
BW
V
C
C
C
B
B
B
C
B
DQ
DQ
WE
C
SS
SS
B
V
V
NC
V
NC
V
V
DDQ
DDQ
DD
DD
DD
K
DQ
DQ
DQ
DQ
DQ
V
CLK
NC
V
DQ
DQ
DQ
DQ
DQ
D
D
D
SS
SS
A
A
A
DQ
DQ
L
M
N
BW
V
BW
A
D
D
D
A
A
A
D
V
V
V
V
DDQ
CEN
A1
DDQ
SS
SS
SS
DQ
V
V
DQ
D
SS
A
P
R
DQ
DQP
A
A0
V
DQP
A
DQ
D
D
SS
SS
A
NC/144M
NC
MODE
V
NC
A
NC/288M
ZZ
DD
NC/72M
TMS
A
A
A
NC/36M
NC
T
U
V
TDI
TCK
TDO
V
DDQ
DDQ
CY7C1373D (1Mx 18)
2
1
3
A
A
A
4
5
A
A
A
6
7
V
A
A
A
V
A
B
C
D
E
F
DDQ
DDQ
NC/576M
NC/1G
CE
NC
NC
NC
DQ
ADV/LD
CE
A
2
3
A
V
DD
DQ
NC
V
NC
CE
V
DQP
B
SS
SS
SS
SS
A
NC
DQ
V
V
V
NC
B
SS
A
1
V
NC
V
DQ
V
DDQ
OE
A
DDQ
SS
A
NC
DQ
NC
NC
DQ
G
H
J
BW
V
B
A
B
DQ
NC
V
DQ
NC
WE
B
SS
SS
A
V
V
NC
V
NC
V
V
DDQ
DDQ
DD
DD
DD
K
NC
DQ
DQ
V
CLK
NC
V
NC
DQ
DQ
B
SS
SS
A
L
M
N
P
NC
DQ
NC
NC
BW
B
A
A
V
V
V
V
V
NC
DQ
V
DDQ
CEN
A1
DDQ
B
SS
SS
SS
SS
DQ
NC
V
V
NC
DQ
B
SS
SS
A
NC
DQP
A0
NC
B
A
R
T
NC/144M
NC/72M
A
A
MODE
A
V
NC
A
A
A
NC/288M
ZZ
DD
NC/36M
TCK
V
TMS
TDI
TDO
NC
V
U
DDQ
DDQ
Document #: 38-05556 Rev. *F
Page 5 of 29
CY7C1371D
CY7C1373D
Pin Configurations (continued)
165-Ball FBGA Pinout
CY7C1371D (512K x 36)
1
2
A
3
CE1
4
BWC
5
BWB
6
CE
7
8
9
A
10
A
11
NC
NC/576M
NC/1G
DQPC
DQC
CEN
WE
VSS
VSS
ADV/LD
A
B
C
D
3
A
CE2
VDDQ
VDDQ
BWD
VSS
BWA
VSS
VSS
CLK
VSS
VSS
OE
VSS
VDD
A
A
NC
NC
DQC
VDDQ
VDDQ
NC
DQPB
DQB
VDD
DQB
DQC
DQC
DQC
DQC
NC
VDDQ
VDDQ
VDDQ
NC
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDDQ
VDDQ
VDDQ
NC
DQB
DQB
DQB
NC
DQB
E
F
DQC
DQC
NC
VSS
VSS
VSS
VSS
VSS
VSS
DQB
DQB
ZZ
G
H
J
DQD
DQD
DQD
DQD
DQD
DQD
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
DQA
DQA
DQA
DQA
DQA
DQA
K
L
DQD
DQD
NC
VDDQ
VDDQ
A
VDD
VSS
A
VSS
NC
VSS
NC
A1
VSS
NC
VDD
VSS
A
VDDQ
VDDQ
A
DQA
NC
A
DQA
DQPA
M
N
P
DQPD
NC/144M NC/72M
TDI
TDO
NC/288M
A0
MODE
NC/36M
A
A
TMS
TCK
A
A
A
A
R
CY7C1373D (1M x 18)
1
NC/576M
NC/1G
NC
2
A
3
CE1
4
BWB
5
NC
6
CE
7
8
9
A
10
A
11
A
CEN
WE
VSS
VSS
ADV/LD
A
B
C
D
3
A
CE2
VDDQ
VDDQ
NC
VSS
VDD
BWA
VSS
VSS
CLK
VSS
VSS
OE
VSS
VDD
A
A
NC
NC
DQB
VDDQ
VDDQ
NC
NC
DQPA
DQA
NC
NC
DQB
DQB
DQB
NC
VDDQ
VDDQ
VDDQ
NC
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDDQ
VDDQ
VDDQ
NC
NC
NC
DQA
E
F
NC
NC
VSS
VSS
VSS
VSS
VSS
VSS
DQA
DQA
ZZ
NC
G
H
J
NC
NC
DQB
DQB
DQB
NC
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
DQA
DQA
DQA
NC
NC
NC
K
L
NC
NC
DQB
NC
NC
VDDQ
VDDQ
A
VDD
VSS
A
VSS
NC
VSS
NC
A1
VSS
NC
VDD
VSS
A
VDDQ
VDDQ
A
DQA
NC
A
NC
NC
M
N
P
DQPB
NC/144M NC/72M
MODE NC/36M
TDI
TDO
NC/288M
A0
A
A
TMS
TCK
A
A
A
A
R
Document #: 38-05556 Rev. *F
Page 6 of 29
CY7C1371D
CY7C1373D
Pin Definitions
Name
IO
Description
Address Inputs used to select one of the address locations. Sampled at the rising edge of the
A , A , A
Input-
0
1
Synchronous CLK. A are fed to the two-bit burst counter.
[1:0]
Input-
Byte Write Inputs, Active LOW. Qualified with WE to conduct writes to the SRAM. Sampled on
BW , BW
A
B
Synchronous the rising edge of CLK.
BW , BW
C
D
WE
Input-
Write Enable Input, Active LOW. Sampled on the rising edge of CLK if CEN is active LOW. This
Synchronous signal must be asserted LOW to initiate a write sequence.
Input-
Advance/Load Input. Used to advance the on-chip address counter or load a new address. When
ADV/LD
Synchronous HIGH (and CEN is asserted LOW) the internal burst counter is advanced. When LOW, a new
address can be loaded into the device for an access. After being deselected, ADV/LD must be
driven LOW to load a new address.
CLK
Input-
Clock
Clock Input. Used to capture all synchronous inputs to the device. CLK is qualified with CEN. CLK
is only recognized if CEN is active LOW.
Input-
Chip Enable 1 Input, Active LOW. Sampled on the rising edge of CLK. Used in conjunction with
CE
CE
1
2
Synchronous CE and CE to select/deselect the device.
2
3
Input-
Chip Enable 2 Input, Active HIGH. Sampled on the rising edge of CLK. Used in conjunction with
Synchronous CE and CE to select/deselect the device.
1
3
Input-
Chip Enable 3 Input, Active LOW. Sampled on the rising edge of CLK. Used in conjunction with
CE
3
Synchronous CE and CE to select/deselect the device.
1
2
Input-
Output Enable, asynchronous input, Active LOW. Combined with the synchronous logic block
OE
Asynchronous inside the device to control the direction of the IO pins. When LOW, the IO pins are allowed to
behave as outputs. When deasserted HIGH, IO pins are tri-stated, and act as input data pins. OE
is masked during the data portion of a write sequence, during the first clock when emerging from
a deselected state, when the device has been deselected.
Input-
Clock Enable Input, Active LOW. When asserted LOW the Clock signal is recognized by the
CEN
ZZ
Synchronous SRAM. When deasserted HIGH the Clock signal is masked. While deasserting CEN does not
deselect the device, use CEN to extend the previous cycle when required.
Input-
ZZ “Sleep” Input. This active HIGH input places the device in a non-time critical “sleep” condition
Asynchronous with data integrity preserved. For normal operation, this pin has to be LOW or left floating. ZZ pin
has an internal pull down.
IO-
Bidirectional Data IO lines. As inputs, they feed into an on-chip data register that is triggered by
DQ
s
Synchronous the rising edge of CLK. As outputs, they deliver the data contained in the memory location specified
by the addresses presented during the previous clock rise of the read cycle. The direction of the
pins is controlled by OE. When OE is asserted LOW, the pins behave as outputs. When HIGH,
DQ and DQP
are placed in a tri-state condition.The outputs are automatically tri-stated during
s
[A:D]
the data portion of a write sequence, during the first clock when emerging from a deselected state,
and when the device is deselected, regardless of the state of OE.
IO-
Bidirectional Data Parity IO Lines. Functionally, these signals are identical to DQ .
DQP
s
X
Synchronous
MODE
Input Strap Pin Mode Input. Selects the burst order of the device.
When tied to Gnd selects linear burst sequence. When tied to V or left floating selects interleaved
DD
burst sequence.
V
V
Power Supply Power supply inputs to the core of the device.
DD
IO Power
Supply
Power supply for the IO circuitry.
DDQ
V
Ground
Ground for the device.
SS
Document #: 38-05556 Rev. *F
Page 7 of 29
CY7C1371D
CY7C1373D
Pin Definitions (continued)
Name
TDO
IO
Description
JTAG serial Serial data-out to the JTAG circuit. Delivers data on the negative edge of TCK. If the JTAG
output feature is not being used, this pin must be left unconnected. This pin is not available on TQFP
Synchronous packages.
TDI
JTAG serial Serial data-In to the JTAG circuit. Sampled on the rising edge of TCK. If the JTAG feature is not
input
being used, this pin can be left floating or connected to V through a pull up resistor. This pin is
DD
Synchronous not available on TQFP packages.
TMS
JTAG serial Serial data-In to the JTAG circuit. Sampled on the rising edge of TCK. If the JTAG feature is not
input
being used, this pin can be disconnected or connected to V . This pin is not available on TQFP
DD
Synchronous packages.
TCK
NC
JTAG-
Clock
Clock input to the JTAG circuitry. If the JTAG feature is not being used, this pin must be
connected to V . This pin is not available on TQFP packages.
SS
–
No Connects. Not internally connected to the die. NC/(36 M, 72 M, 144 M, 288M, 576M, 1G)are
address expansion pins and are not internally connected to the die.
is in progress and allows the requested data to propagate to
the output buffers. The data is available within 6.5 ns
Functional Overview
The CY7C1371D/CY7C1373D is a synchronous flow through
burst SRAM designed specifically to eliminate wait states
during Write-Read transitions. All synchronous inputs pass
through input registers controlled by the rising edge of the
clock. The clock signal is qualified with the Clock Enable input
signal (CEN). If CEN is HIGH, the clock signal is not recog-
nized and all internal states are maintained. All synchronous
operations are qualified with CEN. Maximum access delay
(133-MHz device) provided OE is active LOW. After the first
clock of the read access, the output buffers are controlled by
OE and the internal control logic. OE must be driven LOW in
order for the device to drive out the requested data. On the
subsequent clock, another operation (Read/Write/Deselect)
can be initiated. When the SRAM is deselected at clock rise
by one of the chip enable signals, its output is tri-stated
immediately.
from the clock rise (t
) is 6.5 ns (133-MHz device).
CDV
Burst Read Accesses
Accesses can be initiated by asserting all three Chip Enables
(CE , CE , CE ) active at the rising edge of the clock. If Clock
The CY7C1371D/CY7C1373D has an on-chip burst counter
that allows the user the ability to supply a single address and
conduct up to four Reads without reasserting the address
inputs. ADV/LD must be driven LOW to load a new address
into the SRAM, as described in the Single Read Access
section above. The sequence of the burst counter is deter-
mined by the MODE input signal. A LOW input on MODE
selects a linear burst mode, a HIGH selects an interleaved
1
2
3
Enable (CEN) is active LOW and ADV/LD is asserted LOW,
the address presented to the device is latched. The access
can either be a read or write operation, depending on the
status of the Write Enable (WE). BW can be used to conduct
byte write operations.
X
Write operations are qualified by the Write Enable (WE). All
writes are simplified with on-chip synchronous self-timed write
circuitry.
burst sequence. Both burst counters use A and A in the burst
0
1
sequence, and wraps around when incremented sufficiently. A
HIGH input on ADV/LD increments the internal burst counter
regardless of the state of chip enable inputs or WE. WE is
latched at the beginning of a burst cycle. Therefore, the type
of access (Read or Write) is maintained throughout the burst
sequence.
Three synchronous Chip Enables (CE , CE , CE ) and an
1
2
3
asynchronous Output Enable (OE) simplify depth expansion.
All operations (Reads, Writes, and Deselects) are pipelined.
ADV/LD must be driven LOW after the device has been
deselected to load a new address for the next operation.
Single Read Accesses
Single Write Accesses
A read access is initiated when these conditions are satisfied
at clock rise:
Write access are initiated when the following conditions are
satisfied at clock rise: (1) CEN is asserted LOW, (2) CE , CE ,
1
2
and CE are ALL asserted active, and (3) the write signal WE
3
• CEN is asserted LOW
is asserted LOW. The address presented to the address bus
is loaded into the Address Register. The write signals are
latched into the Control Logic block. The data lines are
automatically tri-stated regardless of the state of the OE input
signal. This allows the external logic to present the data on
• CE , CE , and CE are ALL asserted active
1
2
3
• The Write Enable input signal WE is deasserted HIGH
• ADV/LD is asserted LOW.
The address presented to the address inputs is latched into
the Address Register and presented to the memory array and
control logic. The control logic determines that a read access
DQs and DQP .
X
On the next clock rise the data presented to DQs and DQP
(or a subset for byte write operations, see truth table for
X
Document #: 38-05556 Rev. *F
Page 8 of 29
CY7C1371D
CY7C1373D
details) inputs is latched into the device and the write is
complete. Additional accesses (Read/Write/Deselect) can be
initiated on this cycle.
clock cycles are required to enter into or exit from this “sleep”
mode. While in this mode, data integrity is guaranteed.
Accesses pending when entering the “sleep” mode are not
considered valid nor is the completion of the operation
guaranteed. The device must be deselected prior to entering
The data written during the Write operation is controlled by
BW signals. The CY7C1371D/CY7C1373D provides byte
X
the “sleep” mode. CE , CE , and CE , must remain inactive
1
2
3
write capability that is described in the truth table. Asserting
the Write Enable input (WE) with the selected Byte Write
Select input selectively writes to only the desired bytes. Bytes
not selected during a byte write operation remains unaltered.
A synchronous self-timed write mechanism has been provided
to simplify the write operations. Byte write capability has been
included to greatly simplify Read/Modify/Write sequences,
which can be reduced to simple byte write operations.
for the duration of t
after the ZZ input returns LOW.
ZZREC
Interleaved Burst Address Table
(MODE = Floating or VDD
)
First
Address
A1: A0
Second
Address
A1: A0
Third
Address
A1: A0
Fourth
Address
A1: A0
Because the CY7C1371D/CY7C1373D is a common IO
device, data must not be driven into the device while the
outputs are active. The Output Enable (OE) can be deasserted
00
01
10
11
01
00
11
10
10
11
00
01
11
10
01
00
HIGH before presenting data to the DQs and DQP inputs.
X
Doing so tri-states the output drivers. As a safety precaution,
DQs and DQP are automatically tri-stated during the data
X
portion of a write cycle, regardless of the state of OE.
Burst Write Accesses
Linear Burst Address Table (MODE = GND)
The CY7C1371D/CY7C1373D has an on-chip burst counter
that allows the user the ability to supply a single address and
conduct up to four Write operations without reasserting the
address inputs. ADV/LD must be driven LOW to load the initial
address, as described in the Single Write Access section
above. When ADV/LD is driven HIGH on the subsequent clock
First
Address
A1: A0
Second
Address
A1: A0
Third
Address
A1: A0
Fourth
Address
A1: A0
00
01
10
11
01
10
11
00
10
11
00
01
11
00
01
10
rise, the Chip Enables (CE , CE , and CE ) and WE inputs are
1
2
3
ignored and the burst counter is incremented. The correct
BW inputs must be driven in each cycle of the burst write, to
X
write the correct bytes of data.
Sleep Mode
The ZZ input pin is an asynchronous input. Asserting ZZ
places the SRAM in a power conservation “sleep” mode. Two
ZZ Mode Electrical Characteristics
Parameter
Description
Sleep mode standby current
Device operation to ZZ
Test Conditions
ZZ > V – 0.2V
Min
Max
80
Unit
mA
ns
I
t
t
t
t
DDZZ
DD
ZZ > V – 0.2V
2t
ZZS
DD
CYC
ZZ recovery time
ZZ < 0.2V
2t
ns
ZZREC
ZZI
CYC
ZZ active to sleep current
ZZ Inactive to exit sleep current
This parameter is sampled
This parameter is sampled
2t
ns
CYC
0
ns
RZZI
Document #: 38-05556 Rev. *F
Page 9 of 29
CY7C1371D
CY7C1373D
Address
Used
Operation
Deselect Cycle
CE CE
ZZ ADV/LD WE BW
X
OE CEN CLK
DQ
CE
X
H
X
X
L
1
2
3
None
None
H
X
X
X
L
X
X
L
L
L
L
L
L
L
L
L
L
L
L
L
L
H
L
L
X
X
X
X
H
X
H
X
L
X
X
X
X
X
X
X
X
L
X
X
X
X
L
L
L
L
L
L
L
L
L
L
L
L
L
H
X
L->H Tri-State
L->H Tri-State
L->H Tri-State
L->H Tri-State
L->H Data Out (Q)
L->H Data Out (Q)
L->H Tri-State
L->H Tri-State
L->H Data In (D)
L->H Data In (D)
L->H Tri-State
L->H Tri-State
Deselect Cycle
Deselect Cycle
None
L
Continue Deselect Cycle
Read Cycle (Begin Burst)
Read Cycle (Continue Burst)
None
X
H
X
H
X
H
X
H
X
X
X
H
L
External
Next
X
L
X
L
H
L
L
NOP/Dummy Read (Begin Burst) External
H
H
X
X
X
X
X
X
Dummy Read (Continue Burst)
Write Cycle (Begin Burst)
Write Cycle (Continue Burst)
NOP/Write Abort (Begin Burst)
Write Abort (Continue Burst)
Ignore Clock Edge (Stall)
Sleep Mode
Next
External
Next
X
L
X
L
H
L
X
L
X
L
H
L
X
L
L
None
H
H
X
X
Next
X
X
X
X
X
X
H
X
X
X
X
X
Current
None
L->H
X
–
Tri-State
Function (CY7C1371D)
WE
BW
BW
BW
BW
D
A
B
C
Read
H
L
L
L
L
L
L
X
H
L
X
H
H
L
X
H
H
H
L
X
H
H
H
H
L
Write No bytes written
Write Byte A – (DQ and DQP )
A
A
Write Byte B – (DQ and DQP )
H
H
H
L
B
B
Write Byte C – (DQ and DQP )
H
H
L
C
C
Write Byte D – (DQ and DQP )
H
L
D
D
Write All Bytes
L
Function (CY7C1373D)
WE
BW
BW
A
B
Read
H
L
L
L
L
X
H
L
X
H
H
L
Write - No bytes written
Write Byte A – (DQ and DQP )
A
A
Write Byte B – (DQ and DQP )
H
L
B
B
Write All Bytes
L
Notes:
2. X = “Don't Care.” H = Logic HIGH, L = Logic LOW. BW = 0 signifies at least one Byte Write Select is active, BW = Valid signifies that the desired byte write
X
X
selects are asserted, see truth table for details.
3. Write is defined by BW , and WE. See truth table for Read/Write.
X
4. When a write cycle is detected, all IOs are tri-stated, even during byte writes.
5. The DQs and DQP pins are controlled by the current cycle and the OE signal. OE is asynchronous and is not sampled with the clock.
X
6. CEN = H, inserts wait states.
7. Device powers up deselected and the IOs in a tri-state condition, regardless of OE.
8. OE is asynchronous and is not sampled with the clock rise. It is masked internally during write cycles. During a read cycle DQs and DQP = Tri-state when OE
X
is inactive or when the device is deselected, and DQs and DQP = data when OE is active.
X
9. Table only lists a partial listing of the byte write combinations. Any Combination of BW is valid Appropriate write is based on which byte write is active.
X
Document #: 38-05556 Rev. *F
Page 10 of 29
CY7C1371D
CY7C1373D
Test Data-In (TDI)
IEEE 1149.1 Serial Boundary Scan (JTAG)
The TDI ball is used to serially input information into the
registers and can be connected to the input of any of the
registers. The register between TDI and TDO is chosen by the
instruction that is loaded into the TAP instruction register. For
information on loading the instruction register, see TAP
Controller State Diagram. TDI is internally pulled up and can
be unconnected if the TAP is unused in an application. TDI is
connected to the most significant bit (MSB) of any register.
(See Tap Controller Block Diagram.)
The CY7C1371D/CY7C1373D incorporates a serial boundary
scan test access port (TAP).This part is fully compliant with
1149.1. The TAP operates using JEDEC-standard 3.3V or
2.5V IO logic levels.
The CY7C1371D/CY7C1373D contains a TAP controller,
instruction register, boundary scan register, bypass register,
and ID register.
Disabling the JTAG Feature
It is possible to operate the SRAM without using the JTAG
feature. To disable the TAP controller, TCK must be tied LOW
Test Data-Out (TDO)
The TDO output ball is used to serially clock data-out from the
registers. The output is active depending upon the current
state of the TAP state machine. The output changes on the
falling edge of TCK. TDO is connected to the least significant
bit (LSB) of any register. (See Tap Controller State Diagram.)
(V ) to prevent clocking of the device. TDI and TMS are inter-
SS
nally pulled up and may be unconnected. They may alternately
be connected to V through a pull up resistor. TDO must be
DD
left unconnected. Upon power up, the device is up in a reset
state which does not interfere with the operation of the device.
TAP Controller Block Diagram
TAP Controller State Diagram
0
TEST-LOGIC
1
RESET
0
Bypass Register
1
1
1
2
1
0
0
0
RUN-TEST/
IDLE
SELECT
DR-SCAN
SELECT
IR-SCAN
0
Selection
Circuitry
Selection
Circuitry
Instruction Register
31 30 29
Identification Register
0
0
TDI
TDO
1
1
.
.
.
2
1
CAPTURE-DR
CAPTURE-IR
0
0
SHIFT-DR
0
SHIFT-IR
0
x
.
.
.
.
.
2
1
1
1
Boundary Scan Register
1
1
EXIT1-DR
EXIT1-IR
0
0
TCK
PAUSE-DR
1
0
PAUSE-IR
1
0
TAP CONTROLLER
TMS
0
0
EXIT2-DR
1
EXIT2-IR
1
Performing a TAP Reset
UPDATE-DR
UPDATE-IR
A RESET is performed by forcing TMS HIGH (V ) for five
DD
1
0
1
0
rising edges of TCK. This RESET does not affect the operation
of the SRAM and may be performed while the SRAM is
operating.
At power up, the TAP is reset internally to ensure that TDO
comes up in a High-Z state.
The 0/1 next to each state represents the value of TMS at the
rising edge of TCK.
TAP Registers
Test Access Port (TAP)
Registers are connected between the TDI and TDO balls and
allow data to be scanned into and out of the SRAM test
circuitry. Only one register can be selected at a time through
the instruction register. Data is serially loaded into the TDI ball
on the rising edge of TCK. Data is output on the TDO ball on
the falling edge of TCK.
Test Clock (TCK)
The test clock is used only with the TAP controller. All inputs
are captured on the rising edge of TCK. All outputs are driven
from the falling edge of TCK.
Test Mode Select (TMS)
Instruction Register
The TMS input is used to give commands to the TAP controller
and is sampled on the rising edge of TCK. It is allowable to
leave this ball unconnected if the TAP is not used. The ball is
pulled up internally, resulting in a logic HIGH level.
Three-bit instructions can be serially loaded into the instruction
register. This register is loaded when it is placed between the
TDI and TDO balls as shown in the Tap Controller Block
Diagram. Upon power up, the instruction register is loaded
with the IDCODE instruction. It is also loaded with the IDCODE
Document #: 38-05556 Rev. *F
Page 11 of 29
CY7C1371D
CY7C1373D
instruction if the controller is placed in a reset state as
described in the previous section.
access between the TDI and TDO in the shift-DR controller
state.
When the TAP controller is in the Capture-IR state, the two
least significant bits are loaded with a binary “01” pattern to
allow for fault isolation of the board level serial test data path.
IDCODE
The IDCODE instruction causes a vendor-specific, 32-bit code
to be loaded into the instruction register. It also places the
instruction register between the TDI and TDO balls and allows
the IDCODE to be shifted out of the device when the TAP
controller enters the Shift-DR state.
Bypass Register
To save time when serially shifting data through registers, it is
sometimes advantageous to skip certain chips. The bypass
register is a single-bit register that can be placed between the
TDI and TDO balls. This allows data to be shifted through the
SRAM with minimal delay. The bypass register is set LOW
The IDCODE instruction is loaded into the instruction register
upon power up or whenever the TAP controller is supplied a
test logic reset state.
(V ) when the BYPASS instruction is executed.
SS
SAMPLE Z
Boundary Scan Register
The SAMPLE Z instruction causes the boundary scan register
to be connected between the TDI and TDO balls when the TAP
controller is in a Shift-DR state. It also places all SRAM outputs
into a High-Z state.
The boundary scan register is connected to all the input and
bidirectional balls on the SRAM.
The boundary scan register is loaded with the contents of the
RAM IO ring when the TAP controller is in the Capture-DR
state and is then placed between the TDI and TDO balls when
the controller is moved to the Shift-DR state. The EXTEST,
SAMPLE/PRELOAD and SAMPLE Z instructions can be used
to capture the contents of the IO ring.
SAMPLE/PRELOAD
SAMPLE/PRELOAD is a 1149.1 mandatory instruction. When
the SAMPLE/PRELOAD instructions are loaded into the
instruction register and the TAP controller is in the Capture-DR
state, a snapshot of data on the inputs and output pins is
captured in the boundary scan register.
The Boundary Scan Order tables show the order in which the
bits are connected. Each bit corresponds to one of the bumps
on the SRAM package. The MSB of the register is connected
to TDI and the LSB is connected to TDO.
The user must be aware that the TAP controller clock can only
operate at a frequency up to 20 MHz, while the SRAM clock
operates more than an order of magnitude faster. Because
there is a large difference in the clock frequencies, it is
possible that during the Capture-DR state, an input or output
undergoes a transition. The TAP may then try to capture a
signal while in transition (metastable state). This does not
harm the device, but there is no guarantee as to the value that
is captured. Repeatable results may not be possible.
Identification (ID) Register
The ID register is loaded with a vendor-specific, 32-bit code
during the Capture-DR state when the IDCODE command is
loaded in the instruction register. The IDCODE is hardwired
into the SRAM and can be shifted out when the TAP controller
is in the Shift-DR state. The ID register has a vendor code and
other information described in the Identification Register
Definitions table.
To guarantee that the boundary scan register captures the
correct value of a signal, the SRAM signal must be stabilized
long enough to meet the TAP controller's capture setup plus
TAP Instruction Set
hold times (t and t ). The SRAM clock input might not be
CS
CH
captured correctly if there is no way in a design to stop (or
slow) the clock during a SAMPLE/PRELOAD instruction. If this
is an issue, it is still possible to capture all other signals and
simply ignore the value of the CK and CK captured in the
boundary scan register.
Overview
Eight different instructions are possible with the three bit
instruction register. All combinations are listed in the
Instruction Codes table. Three of these instructions are listed
as RESERVED and must not be used. The other five instruc-
tions are described in detail below.
After the data is captured, it is possible to shift out the data by
putting the TAP into the Shift-DR state. This places the bound-
ary scan register between the TDI and TDO pins.
Instructions are loaded into the TAP controller during the
Shift-IR state when the instruction register is placed between
TDI and TDO. During this state, instructions are shifted
through the instruction register through the TDI and TDO balls.
To execute the instruction after it is shifted in, the TAP
controller needs to be moved into the Update-IR state.
PRELOAD allows an initial data pattern to be placed at the
latched parallel outputs of the boundary scan register cells pri-
or to the selection of another boundary scan test operation.
The shifting of data for the SAMPLE and PRELOAD phases
can occur concurrently when required—that is, while data
captured is shifted out, the preloaded data can be shifted in.
EXTEST
The EXTEST instruction enables the preloaded data to be
driven out through the system output pins. This instruction also
selects the boundary scan register to be connected for serial
BYPASS
When the BYPASS instruction is loaded in the instruction
register and the TAP is placed in a Shift-DR state, the bypass
register is placed between the TDI and TDO balls. The
advantage of the BYPASS instruction is that it shortens the
Document #: 38-05556 Rev. *F
Page 12 of 29
CY7C1371D
CY7C1373D
boundary scan path when multiple devices are connected
together on a board.
This bit can be set by entering the SAMPLE/PRELOAD or
EXTEST command, and then shifting the desired bit into that
cell, during the “Shift-DR” state. During “Update-DR,” the value
loaded into that shift-register cell latches into the preload
register. When the EXTEST instruction is entered, this bit
directly controls the output Q-bus pins. Note that this bit is
preset HIGH to enable the output when the device is
powered-up, and also when the TAP controller is in the
“Test-Logic-Reset” state.
EXTEST Output Bus Tri-State
IEEE Standard 1149.1 mandates that the TAP controller be
able to put the output bus into a tri-state mode.
The boundary scan register has a special bit located at bit #85
(for 119-BGA package) or bit #89 (for 165-fBGA package).
When this scan cell, called the “extest output bus tri-state,” is
latched into the preload register during the “Update-DR” state
in the TAP controller, it directly controls the state of the output
(Q-bus) pins, when the EXTEST is entered as the current
instruction. When HIGH, it enables the output buffers to drive
the output bus. When LOW, this bit places the output bus into
a High-Z condition.
Reserved
These instructions are not implemented but are reserved for
future use. Do not use these instructions.
TAP Timing
1
2
3
4
5
6
Test Clock
(TCK)
t
t
t
TH
CYC
TL
t
t
t
t
TMSS
TDIS
TMSH
Test Mode Select
(TMS)
TDIH
Test Data-In
(TDI)
t
TDOV
t
TDOX
Test Data-Out
(TDO)
DON’T CARE
UNDEFINED
Document #: 38-05556 Rev. *F
Page 13 of 29
CY7C1371D
CY7C1373D
TAP AC Switching Characteristics Over the Operating Range
Parameter
Clock
Description
Min
Max
Unit
t
t
t
t
TCK Clock Cycle Time
TCK Clock Frequency
TCK Clock HIGH time
TCK Clock LOW time
50
ns
MHz
ns
TCYC
TF
20
20
20
TH
ns
TL
Output Times
t
t
TCK Clock LOW to TDO Valid
TCK Clock LOW to TDO Invalid
10
ns
ns
TDOV
TDOX
0
Setup Times
t
t
t
TMS Setup to TCK Clock Rise
TDI Setup to TCK Clock Rise
Capture Setup to TCK Rise
5
5
5
ns
ns
ns
TMSS
TDIS
CS
Hold Times
t
t
t
TMS Hold after TCK Clock Rise
TDI Hold after Clock Rise
5
5
5
ns
ns
ns
TMSH
TDIH
CH
Capture Hold after Clock Rise
Notes:
10. t and t refer to the setup and hold time requirements of latching data from the boundary scan register.
CS
CH
11. Test conditions are specified using the load in TAP AC test Conditions. t /t = 1 ns.
R
F
Document #: 38-05556 Rev. *F
Page 14 of 29
CY7C1371D
CY7C1373D
3.3V TAP AC Test Conditions
2.5V TAP AC Test Conditions
Input pulse levels ............................................... .V to 3.3V
Input pulse level...................................................V to 2.5V
SS
SS
Input rise and fall times................................................... 1 ns
Input timing reference levels...........................................1.5V
Output reference levels...................................................1.5V
Test load termination supply voltage...............................1.5V
Input rise and fall time .....................................................1 ns
Input timing reference levels........................................ .1.25V
Output reference levels ................................................ 1.25V
Test load termination supply voltage ............................ 1.25V
3.3V TAP AC Output Load Equivalent
2.5V TAP AC Output Load Equivalent
1.25V
1.5V
50Ω
50Ω
TDO
TDO
ZO= 50Ω
20pF
ZO= 50Ω
20pF
TAP DC Electrical Characteristics And Operating Conditions
(0°C < TA < +70°C; VDD = 3.3V ±0.165V unless otherwise noted)
Parameter
Description
Description
= –4.0 mA
Conditions
Min
2.4
2.0
2.9
2.1
Max
Unit
V
V
V
V
V
V
V
Output HIGH Voltage
I
I
I
V
V
V
V
V
V
V
V
V
V
V
V
= 3.3V
= 2.5V
= 3.3V
= 2.5V
= 3.3V
= 2.5V
= 3.3V
= 2.5V
= 3.3V
= 2.5V
= 3.3V
= 2.5V
OH1
OH
OH
OH
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
= –1.0 mA
= –100 µA
V
Output HIGH Voltage
Output LOW Voltage
Output LOW Voltage
Input HIGH Voltage
Input LOW Voltage
Input Load Current
V
OH2
OL1
OL2
IH
V
I
I
I
= 8.0 mA
= 1.0 mA
= 100 µA
0.4
0.4
0.2
0.2
V
OL
OL
OL
V
V
V
2.0
1.7
V
V
+ 0.3
V
DD
DD
+ 0.3
V
–0.5
–0.3
–5
0.7
V
IL
0.7
5
V
I
GND < V < V
DDQ
µA
X
IN
Note:
12. All voltages referenced to V (GND).
SS
Document #: 38-05556 Rev. *F
Page 15 of 29
CY7C1371D
CY7C1373D
Identification Register Definitions
CY7C1371D
(512K X 36)
CY7C1373D
(1M X 18)
Instruction Field
Revision Number (31:29)
Device Depth (28:24)
Description
000
01011
000
Describes the version number
Reserved for internal use
01011
001001
010101
Device Width (23:18)
001001
100101
00000110100
1
Defines memory type and architecture
Defines width and density
Cypress Device ID (17:12)
Cypress JEDEC ID Code (11:1)
ID Register Presence Indicator (0)
00000110100 Allows unique identification of SRAM vendor
Indicates the presence of an ID register
1
Scan Register Sizes
Register Name
Bit Size (x36)
Bit Size (x18)
Instruction
3
3
Bypass
1
1
ID
32
85
89
32
85
89
Boundary Scan Order (119-Ball BGA package)
Boundary Scan Order (165-Ball FBGA package)
Identification Codes
Instruction
EXTEST
Code
Description
000
Captures IO ring contents. Places the boundary scan register between TDI and TDO.
Forces all SRAM outputs to High-Z state.
IDCODE
001
010
Loads the ID register with the vendor ID code and places the register between TDI and
TDO. This operation does not affect SRAM operations.
SAMPLE Z
Captures IO ring contents. Places the boundary scan register between TDI and TDO.
Forces all SRAM output drivers to a High-Z state.
RESERVED
011
100
Do Not Use: This instruction is reserved for future use.
SAMPLE/PRELOAD
Captures IO ring contents. Places the boundary scan register between TDI and TDO.
Does not affect SRAM operation.
RESERVED
RESERVED
BYPASS
101
110
111
Do Not Use: This instruction is reserved for future use.
Do Not Use: This instruction is reserved for future use.
Places the bypass register between TDI and TDO. This operation does not affect SRAM
operations.
Document #: 38-05556 Rev. *F
Page 16 of 29
CY7C1371D
CY7C1373D
Bit #
1
Ball ID
Bit #
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
Ball ID
F6
Bit #
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
Ball ID
G4
A4
G3
C3
B2
B3
A3
C2
A2
B1
C1
D2
E1
F2
Bit #
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
Ball ID
L1
H4
T4
T5
T6
R5
L5
2
E7
D7
H7
G6
E6
D6
C7
B7
C6
A6
C5
B5
G5
B6
D4
B4
F4
M2
N1
3
4
P1
5
K1
6
L2
7
R6
U6
R7
T7
P6
N7
M6
L7
N2
P2
8
9
R3
10
11
12
13
14
15
16
17
18
19
20
21
22
T1
R1
T2
L3
R2
K6
P7
N6
L6
G1
H2
D1
E2
G2
H1
J3
T3
L4
N4
P4
K7
J5
M4
A5
K4
E4
Internal
H6
G7
2K
Notes:
13. Balls which are NC (No Connect) are pre-set LOW.
14. Bit# 85 is pre-set HIGH.
Document #: 38-05556 Rev. *F
Page 17 of 29
CY7C1371D
CY7C1373D
Bit #
1
Ball ID
N6
Bit #
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
Ball ID
D10
C11
A11
B11
A10
B10
A9
Bit #
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
Ball ID
G1
D2
E2
2
N7
3
N10
P11
P8
4
F2
5
G2
H1
H3
J1
6
R8
7
R9
8
P9
B9
9
P10
R10
R11
H11
N11
M11
L11
K11
J11
M10
L10
K10
J10
H9
C10
A8
K1
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
L1
B8
M1
J2
A7
B7
K2
B6
L2
A6
M2
N1
N2
P1
B5
A5
A4
B4
R1
R2
P3
B3
A3
A2
R3
P2
H10
G11
F11
E11
D11
G10
F10
E10
B2
C2
R4
P4
B1
A1
N5
P6
C1
D1
R6
Internal
E1
F1
Note:
15. Bit# 89 is pre-set HIGH.
Document #: 38-05556 Rev. *F
Page 18 of 29
CY7C1371D
CY7C1373D
DC Input Voltage ................................... –0.5V to V + 0.5V
Maximum Ratings
DD
Current into Outputs (LOW)......................................... 20 mA
Exceeding maximum ratings may impair the useful life of the
device. These user guidelines are not tested.
Static Discharge Voltage.......................................... > 2001V
(MIL-STD-883, Method 3015)
Storage Temperature .................................–65°C to +150°C
Latch up Current.................................................... > 200 mA
Ambient Temperature with
Power Applied.............................................–55°C to +125°C
Operating Range
Supply Voltage on V Relative to GND........ –0.5V to +4.6V
DD
Ambient
Range
Temperature
V
V
DDQ
Supply Voltage on V
Relative to GND ......–0.5V to +V
DD
DD
DDQ
Commercial 0°C to +70°C 3.3V – 5%/+10% 2.5V – 5%
DC Voltage Applied to Outputs
in Tri-State........................................... –0.5V to V
to V
+ 0.5V
DD
Industrial
–40°C to +85°C
DDQ
Electrical Characteristics
Over the Operating Range
Parameter
Description
Test Conditions
Min
Max
Unit
V
Power Supply Voltage
IO Supply Voltage
3.135
3.135
2.375
2.4
3.6
V
V
DD
V
V
V
V
V
I
for 3.3V IO
for 2.5V IO
for 3.3V IO, I = –4.0 mA
V
DD
DDQ
2.625
V
Output HIGH Voltage
Output LOW Voltage
V
OH
OL
IH
OH
for 2.5V IO, I = –1.0 mA
2.0
V
OH
for 3.3V IO, I = 8.0 mA
0.4
0.4
V
OL
for 2.5V IO, I = 1.0 mA
V
OL
Input HIGH Voltage
for 3.3V IO
for 2.5V IO
for 3.3V IO
for 2.5V IO
2.0
1.7
V
V
+ 0.3V
V
DD
+ 0.3V
V
DD
Input LOW Voltage
–0.3
–0.3
–5
0.8
V
IL
0.7
5
V
Input Leakage Current GND ≤ V ≤ V
except ZZ and MODE
µA
X
I
DDQ
Input Current of MODE Input = V
–30
–5
µA
µA
SS
Input = V
5
DD
Input Current of ZZ
Input = V
Input = V
µA
SS
DD
30
µA
I
I
V
Operating Supply
V
f = f
= Max., I
= 0 mA,
7.5 ns cycle, 133 MHz
10 ns cycle, 100 MHz
210
175
140
120
mA
mA
mA
mA
DD
DD
DD
OUT
= 1/t
MAX CYC
Current
Automatic CE
Power down
Current—TTL Inputs
V = Max, Device Deselected, 7.5 ns cycle, 133 MHz
DD
SB1
SB2
SB3
SB4
V
≥ V or V ≤ V
IN
IH IN IL
10 ns cycle, 100 MHz
f = f
, inputs switching
MAX
I
I
I
Automatic CE
Power down
Current—CMOS Inputs f = 0, inputs static
V
V
= Max, Device Deselected, All speeds
≤ 0.3V or V > V – 0.3V,
70
mA
DD
IN
IN
DD
Automatic CE
Power down
Current—CMOS Inputs f = f
V
V
= Max, Device Deselected, or 7.5 ns cycle, 133 MHz
130
110
mA
mA
DD
≤ 0.3V or V > V – 0.3V
IN
IN
DDQ
10 ns cycle, 100 MHz
, inputs switching
MAX
Automatic CE
Power down
Current—TTL Inputs
V
V
= Max, Device Deselected, All Speeds
80
mA
DD
≥ V – 0.3V or V
≤
, f =
IN
DD
IN 0.3V
0, inputs static
Notes:
16. Overshoot: V (AC) < V +1.5V (Pulse width less than t
/2), undershoot: V (AC) > –2V (Pulse width less than t /2).
CYC
IH
DD
CYC
IL
17. T
: Assumes a linear ramp from 0V to V (min.) within 200 ms. During this time V < V and V
< V
.
Power-up
DD
IH
DD
DDQ
DD
Document #: 38-05556 Rev. *F
Page 19 of 29
CY7C1371D
CY7C1373D
Capacitance[18]
100 TQFP
Package
119 BGA
Package
165 FBGA
Parameter
Description
Test Conditions
Package
Unit
pF
C
C
C
Input Capacitance
T = 25°C, f = 1 MHz,
5
5
5
8
8
8
9
9
9
IN
A
V
V
= 3.3V
= 2.5V
DD
Clock Input Capacitance
Input/Output Capacitance
pF
CLK
IO
DDQ
pF
Thermal Resistance[18]
100 TQFP
Package
119 BGA
Package
165 FBGA
Package
Parameter
Description
Test Conditions
Unit
Θ
Thermal Resistance
(Junction to Ambient)
Test conditions follow standard
test methods and procedures
for measuring thermal
impedance, according to
EIA/JESD51.
28.66
23.8
20.7
°C/W
JA
Θ
Thermal Resistance
(Junction to Case)
4.08
6.2
4.0
°C/W
JC
AC Test Loads and Waveforms
3.3V IO Test Load
R = 317Ω
3.3V
OUTPUT
ALL INPUT PULSES
90%
VDDQ
GND
OUTPUT
90%
10%
Z = 50Ω
0
R = 50Ω
10%
L
5 pF
R = 351Ω
≤ 1ns
≤ 1ns
V = 1.5V
T
INCLUDING
JIG AND
SCOPE
(c)
(a)
(b)
2.5V IO Test Load
R = 1667Ω
2.5V
OUTPUT
R = 50Ω
OUTPUT
ALL INPUT PULSES
90%
VDDQ
GND
90%
10%
Z = 50Ω
0
10%
L
5 pF
R = 1538Ω
≤ 1ns
≤ 1ns
V = 1.25V
T
INCLUDING
JIG AND
SCOPE
(c)
(a)
(b)
Note:
18. Tested initially and after any design or process change that may affect these parameters.
Document #: 38-05556 Rev. *F
Page 20 of 29
CY7C1371D
CY7C1373D
Switching Characteristics Over the Operating Range
133 MHz
100 MHz
Parameter
Description
Min
Max
Min
Max
Unit
t
1
1
ms
POWER
Clock
t
t
t
Clock Cycle Time
Clock HIGH
7.5
2.1
2.1
10
2.5
2.5
ns
ns
ns
CYC
CH
Clock LOW
CL
Output Times
t
t
t
t
t
t
t
Data Output Valid After CLK Rise
Data Output Hold After CLK Rise
6.5
8.5
ns
ns
ns
ns
ns
ns
ns
CDV
DOH
CLZ
2.0
2.0
2.0
2.0
Clock to Low-Z
Clock to High-Z
4.0
3.2
5.0
3.8
CHZ
OEV
OELZ
OEHZ
OE LOW to Output Valid
OE LOW to Output Low-Z
0
0
OE HIGH to Output High-Z
4.0
5.0
Setup Times
t
t
t
t
t
t
Address Setup Before CLK Rise
ADV/LD Setup Before CLK Rise
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
ns
ns
ns
ns
ns
ns
AS
ALS
WES
CENS
DS
WE, BW Setup Before CLK Rise
X
CEN Setup Before CLK Rise
Data Input Setup Before CLK Rise
Chip Enable Setup Before CLK Rise
CES
Hold Times
t
t
t
t
t
t
Address Hold After CLK Rise
ADV/LD Hold After CLK Rise
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
ns
ns
ns
ns
ns
ns
AH
ALH
WEH
CENH
DH
WE, BW Hold After CLK Rise
X
CEN Hold After CLK Rise
Data Input Hold After CLK Rise
Chip Enable Hold After CLK Rise
CEH
Notes:
19. This part has a voltage regulator internally; t
is the time that the power needs to be supplied above V (minimum) initially, before a read or write operation
DD
POWER
can be initiated.
20. t
, t
, t
, and t
are specified with AC test conditions shown in part (b) of AC Test Loads. Transition is measured ± 200 mV from steady-state voltage.
CHZ CLZ OELZ
OEHZ
21. At any voltage and temperature, t
is less than t
and t
is less than t
to eliminate bus contention between SRAMs when sharing the same data bus.
CLZ
OEHZ
OELZ
CHZ
These specifications do not imply a bus contention condition, but reflect parameters guaranteed over worst case user conditions. Device is designed to achieve
High-Z prior to Low-Z under the same system conditions.
22. This parameter is sampled and not 100% tested.
23. Timing reference level is 1.5V when V
= 3.3V and is 1.25V when V
= 2.5V.
DDQ
DDQ
24. Test conditions shown in (a) of AC Test Loads unless otherwise noted.
Document #: 38-05556 Rev. *F
Page 21 of 29
CY7C1371D
CY7C1373D
Switching Waveforms
Read/Write Waveforms
t
1
2
3
4
5
6
7
8
9
10
CYC
t
CLK
t
t
t
t
t
CENS
CES
CENH
CEH
CL
CH
CEN
CE
ADV/LD
W E
BW
X
A1
A2
A4
A3
A5
A6
A7
ADDRESS
DQ
t
CDV
t
t
AS
AH
t
t
t
t
CHZ
DOH
OEV
CLZ
D(A1)
t
D(A2)
D(A2+1)
Q(A3)
Q(A4)
Q(A4+1)
D(A5)
Q(A6)
D(A7)
t
OEHZ
t
DS
DH
t
DOH
t
OELZ
OE
COM M AND
W RITE
D(A1)
W RITE
D(A2)
BURST
W RITE
READ
Q(A3)
READ
Q(A4)
BURST
READ
W RITE
D(A5)
READ
Q(A6)
W RITE
D(A7)
DESELECT
D(A2+1)
Q(A4+1)
DON’T CARE
UNDEFINED
Notes:
For this waveform ZZ is tied LOW.
25.
26. When CE is LOW, CE is LOW, CE is HIGH and CE is LOW. When CE is HIGH, CE is HIGH or CE is LOW or CE is HIGH.
1
2
3
1
2
3
27. Order of the Burst sequence is determined by the status of the MODE (0 = Linear, 1 = Interleaved). Burst operations are optional.
Document #: 38-05556 Rev. *F
Page 22 of 29
CY7C1371D
CY7C1373D
Switching Waveforms (continued)
NOP, STALL AND DESELECT Cycles
1
2
3
4
5
6
7
8
9
10
CLK
CEN
CE
ADV/LD
WE
BW [A:D]
ADDRESS
A1
A2
A3
A4
A5
t
CHZ
D(A1)
Q(A2)
Q(A3)
D(A4)
Q(A5)
DQ
t
DOH
COMMAND
WRITE
D(A1)
READ
Q(A2)
STALL
READ
Q(A3)
WRITE
D(A4)
STALL
NOP
READ
Q(A5)
DESELECT
CONTINUE
DESELECT
DON’T CARE
UNDEFINED
Note:
28. The IGNORE CLOCK EDGE or STALL cycle (Clock 3) illustrates CEN being used to create a pause. A write is not performed during this cycle.
Document #: 38-05556 Rev. *F
Page 23 of 29
CY7C1371D
CY7C1373D
Switching Waveforms (continued)
ZZ Mode Timing
CLK
t
t
ZZ
ZZREC
ZZ
t
ZZI
I
SUPPLY
I
DDZZ
t
RZZI
ALL INPUTS
(except ZZ)
DESELECT or READ Only
Outputs (Q)
High-Z
DON’T CARE
Notes:
29. Device must be deselected when entering ZZ mode. See truth table for all possible signal conditions to deselect the device.
30. DQs are in high-Z when exiting ZZ sleep mode.
Document #: 38-05556 Rev. *F
Page 24 of 29
CY7C1371D
CY7C1373D
Ordering Information
Not all of the speed, package and temperature ranges are available. Please contact your local sales representative or
Speed
(MHz)
Package
Diagram
Operating
Range
Ordering Code
Part and Package Type
133 CY7C1371D-133AXC
CY7C1373D-133AXC
CY7C1371D-133BGC
CY7C1373D-133BGC
CY7C1371D-133BGXC
CY7C1373D-133BGXC
CY7C1371D-133BZC
CY7C1373D-133BZC
CY7C1371D-133BZXC
CY7C1373D-133BZXC
CY7C1371D-133AXI
CY7C1373D-133AXI
CY7C1371D-133BGI
CY7C1373D-133BGI
CY7C1371D-133BGXI
CY7C1373D-133BGXI
CY7C1371D-133BZI
CY7C1373D-133BZI
CY7C1371D-133BZXI
CY7C1373D-133BZXI
100 CY7C1371D-100AXC
CY7C1373D-100AXC
CY7C1371D-100BGC
CY7C1373D-100BGC
CY7C1371D-100BGXC
CY7C1373D-100BGXC
CY7C1371D-100BZC
CY7C1373D-100BZC
CY7C1371D-100BZXC
CY7C1373D-100BZXC
CY7C1371D-100AXI
CY7C1373D-100AXI
CY7C1371D-100BGI
CY7C1373D-100BGI
CY7C1371D-100BGXI
CY7C1373D-100BGXI
CY7C1371D-100BZI
CY7C1373D-100BZI
CY7C1371D-100BZXI
CY7C1373D-100BZXI
51-85050 100-Pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Pb-Free
Commercial
51-85115 119-Ball Grid Array (14 x 22 x 2.4 mm)
51-85115 119-Ball Grid Array (14 x 22 x 2.4 mm) Pb-Free
51-85180 165-Ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4 mm)
51-85180 165-Ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free
51-85050 100-Pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Pb-Free
51-85115 119-Ball Grid Array (14 x 22 x 2.4 mm)
lndustrial
51-85115 119-Ball Grid Array (14 x 22 x 2.4 mm) Pb-Free
51-85180 165-Ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4 mm)
51-85180 165-Ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free
51-85050 100-Pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Pb-Free
51-85115 119-Ball Grid Array (14 x 22 x 2.4 mm)
Commercial
51-85115 119-Ball Grid Array (14 x 22 x 2.4 mm) Pb-Free
51-85180 165-Ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4 mm)
51-85180 165-Ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free
51-85050 100-Pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Pb-Free
51-85115 119-Ball Grid Array (14 x 22 x 2.4 mm)
lndustrial
51-85115 119-Ball Grid Array (14 x 22 x 2.4 mm) Pb-Free
51-85180 165-Ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4 mm)
51-85180 165-Ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free
Document #: 38-05556 Rev. *F
Page 25 of 29
CY7C1371D
CY7C1373D
Package Diagrams
Figure 1. 100-Pin Thin Plastic Quad Flatpack (14 x 20 x 1.4 mm), 51-85050
16.00 0.20
14.00 0.10
1.40 0.05
100
81
80
1
0.30 0.08
0.65
TYP.
12° 1°
(8X)
SEE DETAIL
A
30
51
31
50
0.20 MAX.
1.60 MAX.
R 0.08 MIN.
0.20 MAX.
0° MIN.
SEATING PLANE
STAND-OFF
0.05 MIN.
0.15 MAX.
NOTE:
1. JEDEC STD REF MS-026
0.25
GAUGE PLANE
2. BODY LENGTH DIMENSION DOES NOT INCLUDE MOLD PROTRUSION/END FLASH
MOLD PROTRUSION/END FLASH SHALL NOT EXCEED 0.0098 in (0.25 mm) PER SIDE
BODY LENGTH DIMENSIONS ARE MAX PLASTIC BODY SIZE INCLUDING MOLD MISMATCH
R 0.08 MIN.
0.20 MAX.
0°-7°
3. DIMENSIONS IN MILLIMETERS
0.60 0.15
0.20 MIN.
1.00 REF.
51-85050-*B
DETAIL
A
Document #: 38-05556 Rev. *F
Page 26 of 29
CY7C1371D
CY7C1373D
Package Diagrams (continued)
Figure 2. 119-Ball BGA (14 x 22 x 2.4 mm) (51-85115)
Ø0.05 M C
Ø0.25 M C A B
A1 CORNER
Ø0.75 0.15(119X)
Ø1.00(3X) REF.
1
2
3
4
5
6
7
7
6
5
4
3
2
1
A
B
C
D
E
A
B
C
D
E
F
F
G
H
G
H
J
K
L
J
K
L
M
N
P
R
T
M
N
P
R
T
U
U
1.27
0.70 REF.
A
3.81
12.00
7.62
B
14.00 0.20
0.15(4X)
30° TYP.
SEATING PLANE
C
51-85115-*B
Document #: 38-05556 Rev. *F
Page 27 of 29
CY7C1371D
CY7C1373D
Package Diagrams (continued)
Figure 3. 165-Ball FBGA (13 x 15 x 1.4 mm) (51-85180)
BOTTOM VIEW
PIN 1 CORNER
TOP VIEW
Ø0.05 M C
Ø0.25 M C A B
PIN 1 CORNER
-0.06
Ø0.50 (165X)
+0.14
1
2
3
4
5
6
7
8
9
10
11
11 10
9
8
7
6
5
4
3
2
1
A
B
A
B
C
D
C
D
E
E
F
F
G
G
H
J
H
J
K
K
L
L
M
M
N
P
R
N
P
R
A
A
1.00
5.00
10.00
13.00 0.10
B
13.00 0.10
B
0.15(4X)
NOTES :
SOLDER PAD TYPE : NON-SOLDER MASK DEFINED (NSMD)
PACKAGE WEIGHT : 0.475g
JEDEC REFERENCE : MO-216 / DESIGN 4.6C
PACKAGE CODE : BB0AC
SEATING PLANE
C
51-85180-*A
NoBL and No Bus Latency are trademarks of Cypress Semiconductor Corporation. ZBT is a trademark of Integrated Device
Technology, Inc. All product and company names mentioned in this document are the trademarks of their respective holders.
Document #: 38-05556 Rev. *F
Page 28 of 29
© Cypress Semiconductor Corporation, 2004-2007. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the
use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to
be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its
products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress
products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
CY7C1371D
CY7C1373D
Document History Page
Document Title: CY7C1371D/CY7C1373D 18-Mbit (512K x 36/1 Mbit x 18) flow through SRAM with NoBL™ Architecture
Document Number: 38-05556
Issue
Date
Orig. of
Change
REV. ECN NO.
Description of Change
**
254513 See ECN
288531 See ECN
RKF
SYT
New data sheet
*A
Edited description under “IEEE 1149.1 Serial Boundary Scan (JTAG)” for
non-compliance with 1149.1
Removed 117 Mhz Speed Bin
Added Pb-free information for 100-Pin TQFP, 119 BGA and 165 FBGA Packages
Added comment of ‘Pb-free BG packages availability’ below the Ordering Infor-
mation
*B
326078 See ECN
PCI
Address expansion pins/balls in the pinouts for all packages are modified
according to JEDEC standard
Added description on EXTEST Output Bus Tri-State
Changed description on the Tap Instruction Set Overview and Extest
Changed Θ and Θ for TQFP Package from 31 and 6 °C/W to 28.66 and 4.08
JA
JC
°C/W respectively
Changed Θ and Θ for BGA Package from 45 and 7 °C/W to 23.8 and 6.2 °C/W
JA
JC
respectively
Changed Θ and Θ for FBGA Package from 46 and 3 °C/W to 20.7 and 4.0
JA
JC
°C/W respectively
Modified V
V
test conditions
OL, OH
Removed comment of ‘Pb-free BG packages availability’ below the Ordering Infor-
mation
Updated Ordering Information Table
*C
*D
345117 See ECN
416321 See ECN
PCI
Updated Ordering Information Table
Changed from Preliminary to Final
NXR
Changed address of Cypress Semiconductor Corporation on Page# 1 from “3901
North First Street” to “198 Champion Court”
In the Partial Truth Table for Read/Write on page # 10, the BW of Write Byte A –
A
(DQ and DQP ) and BW of Write Byte B – (DQ and DQP ) has been changed
A
A
B
B
B
from H to L
Changed the description of I from Input Load Current to Input Leakage Current
X
on page# 20
Changed the Ix current values of MODE on page # 20 from -5 µA and 30 µA
to -30 µA and 5 µA
Changed the Ix current values of ZZ on page # 20 from -30 µA and 5 µA
to -5 µA and 30 µA
Changed V < V to V < V on page # 20
IH
DD
IH
DD
Replaced Package Name column with Package Diagram in the Ordering
Information table
Updated Ordering Information Table
*E
*F
475677 See ECN
VKN
Added the Maximum Rating for Supply Voltage on V
Relative to GND
DDQ
Changed t , t from 25 ns to 20 ns and t
from 5 ns to 10 ns in TAP AC
TH TL
TDOV
Switching Characteristics table.
Updated the Ordering Information table.
1274734 See ECN VKN/AESA Corrected typo in the “NOP, STALL and DESELECT Cycles” waveform
Document #: 38-05556 Rev. *F
Page 29 of 29
|
Electrolux 922069 User Manual
Eizo FLEXSCAN SX3031W User Manual
Dell W880P User Manual
Dell Computer Monitor ST2321L User Manual
Cres Cor CO 151 F 1818B User Manual
AT T E5927B User Manual
AT T 91 001105 040 100 User Manual
Asus P4T CM User Manual
Asus Computer Monitor VH196 User Manual
Asus Computer Monitor VE208 User Manual